Otto Nemenz International, Inc. - Motion Picture Equipement Rentals

535A
Formats	35mm, Super 35
Lens Mount	54mm PL, adjustable for Super 35
Viewfinder	Swingover finder rotates 210° for left or right side operation with fully upright image in any position; Telescoping finder extender; Programmable ArriGlow; 2x magnification; contrast viewing filter; 3-way beamsplitter; Heated eyecup
Viewfinder Magnification	6.5x or 13x with 10x super eyepiece; 5.2x or 10.4x with 8x eyepiece
Mirror Shutter	Single blade 11°-180° electronically and steplessly controlled variable shutter; on-camera shutter openings of 144°, 172.8°, and 180° unique programmable shutterangle / frame rate changes with CCU; angle selected on-board with SCU and off-camera with RU or CCU; mechanically adjustable through lens opening
Viewfinder Displays	Out-of-sync; low battery; film end warning; up to 3 simultaneous ArriGlow formats
Camera Displays	Frame rate; exposed film count; shutter opening; exposed film per take; battery status; time code; user bits; behind-the-lens filter indicator; out of sync; film jam; film end;movement position; magazine improperly mounted; sprocket guides disengaged; running light is green when ready, red when not
Filming Speeds	Built-in control for 24, 25, 29.97, & 30 fps. Speeds continuously variable from 3 to 50 fps using VSU or RU and can be controlled at 0.001 fps increments with CCU; shutter angle can compensate for speed changes during shot with CCU; reverse filming at 24 & 25 fps or from 3 to 30 fps using Laptop Camera Controller.
Run Test	At STANDBY approximately 1 fps
Phase Shifter	Phase Shift button in STANDBY is inching button; in RUN, it is phase shifter; ESU can also be used for phase shift lockup
Beamsplitter Ratios	Viewfinder:Video: Switchable 80:20, 50:50, 10:90
Contrast Filters	Switchable ND .03, ND .06
Movement	Multi-link film transport with dual pin registration and dual pin pulldown claws; adjustable pitch control; reverse running; universal aperture plate with interchangeable format masks
Drive System	Quartz-controlled disk-type DC motor
Power Requirements	24v DC
Power Consumption	Approx. 2a at 24/25 fps with 400' load
Magazines	1000' (300m) and 400' (120m) coaxial, 400' displacement for Steadicam, with dedicated torque motors and LCD & mechanical footage counter; connection and data transfer to camera via multi-pin plug; time code sensitivity selector
Time Code	Standard 535 plug-in time code module for recording SMPTE RP135 and RP 136 80-bit SMPTE time code
Video Assist	Plug-in Video Optics Module with flicker reduction, frame storage, frame store comparison, BNC output and Gen Lock (VD) input
Dimensions	With standard viewfinder, 400' magazine, no lens: Width: 13.7" (349mm) Height: 11.0" (279mm) Length: 19.3" (490mm)
Temperature Range	-4°F (-20°C) to +122°F (+50°C)

535B

Formats

35mm, Super 35

Lens Mount

54mm PL, adjustable for Super 35

Viewfinder

Lightweight modular swingover finder pivots on two axes for left or right side operation with fully upright image in any position; finder extender with 2x magnification; contrast viewing filter; heated eyecup

Viewfinder Magnification

6.5x or 13x with 10x super eyepiece; 5.2x or 10.4x with 8x eyepiece

Mirror Shutter

Single blade 15°-180° mechanically variable shutter, variable in 15° increments plus 144° and 178.2° stops

Viewfinder Displays

Out-of-sync; low battery; film end warning; ArriGlow formats

Camera Displays

Frame rate; exposed film count; battery status; time code; user bits; behind-the-lens filter indicator; out of sync; film jam; film end; movement position; magazine improperly mounted; sprocket guides disengaged; running light is green when ready, red when not

Filming Speeds

Built-in control for 24, 25, 29.97, & 30 fps. Speeds variable from 3 to 60 fps in 0.001 fps increments on camera or remotely controlled by CCU or continuously variable using RU

Run Test

At STANDBY approximately 1 fps

Phase Shifter

Phase Shift button in STANDBY is inching button; in RUN, it is phase shifter; ESU can also be used for phase shift lockup

Beamsplitter Ratios

Viewfinder:Video: Prisms available are 80:20, 50:50, or 10:90

Contrast Filters

Switchable ND .06

Movement

Multi-link film transport with dual pin registration and dual pin pulldown claws; adjustable pitch control; reverse running; universal aperture plate with interchangeable format masks

Drive System

Quartz-controlled disk-type DC motor

Power Requirements

24v DC

Power Consumption

Approx. 2a at 24/25 fps with 400' load

Magazines

1000' (300m) and 400' (120m) coaxial, 400' displacement for Steadicam, with dedicated torque motors and LCD & mechanical footage counter; connection and data transfer to camera via multi-pin plug; time code sensitivity selector

Time Code

Standard 535 plug-in time code module for recording SMPTE RP135 and RP 136 80-bit SMPTE time code

Video Assist

Plug-in Video Optics Module with flicker reduction, frame storage, frame store comparison, BNC output and Gen Lock (VD) input

Dimensions

With standard viewfinder, 400' magazine, no lens:

Width: 11.8" (300mm) (with finder on left)

Height: 11.1" (280mm) (with grip which adds 2")

Length: 19.3" (490mm)

Temperature Range

-4° F (-20°C) to +122°F (+50°C)

535B
Formats	35mm, Super 35
Lens Mount	54mm PL, adjustable for Super 35
Viewfinder	Lightweight modular swingover finder pivots on two axes for left or right side operation with fully upright image in any position; finder extender with 2x magnification; contrast viewing filter; heated eyecup
Viewfinder Magnification	6.5x or 13x with 10x super eyepiece; 5.2x or 10.4x with 8x eyepiece
Mirror Shutter	Single blade 15°-180° mechanically variable shutter, variable in 15° increments plus 144° and 178.2° stops
Viewfinder Displays	Out-of-sync; low battery; film end warning; ArriGlow formats
Camera Displays	Frame rate; exposed film count; battery status; time code; user bits; behind-the-lens filter indicator; out of sync; film jam; film end; movement position; magazine improperly mounted; sprocket guides disengaged; running light is green when ready, red when not
Filming Speeds	Built-in control for 24, 25, 29.97, & 30 fps. Speeds variable from 3 to 60 fps in 0.001 fps increments on camera or remotely controlled by CCU or continuously variable using RU
Run Test	At STANDBY approximately 1 fps
Phase Shifter	Phase Shift button in STANDBY is inching button; in RUN, it is phase shifter; ESU can also be used for phase shift lockup
Beamsplitter Ratios	Viewfinder:Video: Prisms available are 80:20, 50:50, or 10:90
Contrast Filters	Switchable ND .06
Movement	Multi-link film transport with dual pin registration and dual pin pulldown claws; adjustable pitch control; reverse running; universal aperture plate with interchangeable format masks
Drive System	Quartz-controlled disk-type DC motor
Power Requirements	24v DC
Power Consumption	Approx. 2a at 24/25 fps with 400' load
Magazines	1000' (300m) and 400' (120m) coaxial, 400' displacement for Steadicam, with dedicated torque motors and LCD & mechanical footage counter; connection and data transfer to camera via multi-pin plug; time code sensitivity selector
Time Code	Standard 535 plug-in time code module for recording SMPTE RP135 and RP 136 80-bit SMPTE time code
Video Assist	Plug-in Video Optics Module with flicker reduction, frame storage, frame store comparison, BNC output and Gen Lock (VD) input
Dimensions	With standard viewfinder, 400' magazine, no lens: Width: 11.8" (300mm) (with finder on left) Height: 11.1" (280mm) (with grip which adds 2") Length: 19.3" (490mm)
Temperature Range	-4° F (-20°C) to +122°F (+50°C)